Dies ist eine alte Version des Dokuments!
Western Digital WDC NAS Red Harddiscs
WD Green - Desktopfestplatten
Laut Western Digital sind ihre Platten der Serie „Green“ besonders umweltfreundlich. Das finde ich grundsätzlich nicht verkehrt. Leider scheinen aber alle diese Platten einen kritischen Konfigurationsfehler zu haben. Standardmäßig parken diese Platten ihre Schreib-/Leseköpfe nach fünf Sekunden Nichtbenutzung außerhalb des Plattenstapels, um Energie zu sparen. Das Feature hat die Firma „IntelliPark“ getauft. Das klingt nicht schlecht, ist es aber, wenn man die Herstellerspezifikation gelesen hat. Für lediglich 300.000 Parkvorgänge sind diese Festplatten ausgelegt. Noch schlechter wird es einem, wenn man bedenkt, dass Linuxmaschinen normalerweise nach ca. zehn bis 30 Sekunden die Dateisystemcaches auf die Platten wegschreiben.
Bereits nach 13 Stunden in Betrieb war der Zähler der Parkvorgänge - Load Cycle Count - meiner neuen Platte bereits bei über 400. Meine anderen Platten haben nach mehreren Jahren jeweils nur knappe 2000 dieser Parkvorgänge.
Quelle1)
If you have a Western Digital EADS or EARS drive, please check you SMART information before it's too late :
$ sudo smartctl -A /dev/sda | grep "^193" 193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 14493
If the Load cycle count exceeds 1000, you're probably affected by the idle3 timer problem.
Syntax
idle3ctl [options] /dev/device -h : display help -l : show license and exit immediately -V : show version and exit immediately -v : verbose output --force : force even if no Western Digital HDD are detected -g : get raw idle3 timer value (default action) -g100 : get idle3 timer value as wdidle3 v1.00 would display it -g103 : get idle3 timer value as wdidle3 v1.03/v1.05 would display it -d : disable idle3 timer -s<value> : set idle3 timer raw value (1-255)
Get idle3 timer raw value
# idle3ctl -g /dev/sda
Disable idle3 timer
# idle3ctl -d /dev/sda
Set the idle3 timer to 10s
# idle3ctl -s 100 /dev/sda
Idle3ctl should be compatible with all modern Western Digital HDD driven by a real SATA controler. Compatibility with SATA-to-USB adapters is uncertain. Since idle3ctl uses SMART ATA commands to get and set the idle3 timer, it should work if SMART information can be read from your drive.
The idle3 timer seems to be a power on only setting. That means that the drive needs to be powered OFF and then ON to use the new setting.
Source code and releases can be found on the SourceForge project pages.
After downloading the tarball, for example the 0.9.1 release (idle3-tools-0.9.1.tar.gz), uncompress it :
$ tar xzvf idle3-tools-0.9.1.tar.gz
Change to the source directory, and compile the tool :
$ cd idle3-tools-0.9.1 $ make
You should get the idle3ctl executable :
$ ls idle3ctl idle3ctl $ ./idle3ctl -V idle3ctl v0.9.1
And run it with root permissions to get or set the idle3 value :
$ sudo ./idle3ctl -g /dev/sda
Now you can optionnally install the tool to the /sbin directory
$ sudo make install
Please note that, as the idle3 setting of your disk is permanent, you only need to run idle3ctl once per drive.